Adesso CNDV-50MT Service Manual download pdf (Page 72)

Appendix

Route calculation was not possible. Route calculation has failed because

of malfunction of map data, software,

hardware, or disc.

• Change the destination.

• Clean the disc.

• Consult the Pioneer Local dealer if

this message persists.

Route calculation was not possible

because the destination is too far.

The destination is too far. • Set a destination closer to the start-

ing point.

• Set one or more way points.

Route calculation was not possible

because the destination is too near.

The destination or way point(s) is too

close.

Set a destination [and way point(s)]

farther from the starting point.

Route calculation was not possible

due to traffic regulations.

• The destination or way point(s) are

in a Control Traffic Zone (CTR) and

the route calculation is hampered.

• Your vehicle is currently in a Con-

trol Traffic Zone (CTR) and the route

calculation is hampered.

• Set a destination and way point(s)

outside the CTR if you know where

the restricted area is.

• Try the destination or way point(s)

away from the currently set points to

some extent.

• Drive your vehicle to an unre-

stricted area and reset the destina-

tion and way point(s).

Route calculation was not possible

because no guidance can be pro-

vided around the destination or the

starting point.

The destination, way point(s), or

starting point are in an area where

no road exists (e.g. a mountain) and

the route calculation is impossible.

• Set a destination and way point(s)

on roads.

• Reset the destination after you

drive the vehicle to any road.

There is no route to the destination. The destination or way point(s) are in

an isolated island, etc. without a ferry

and the route calculation is impossi-

ble.

Change the destination.

The route could not avoid the speci-

fied area.

If route setting cannot avoid speci-

fied Areas to Avoid.

If the current route is not desired, set

destination or way points that do not

pass through the Areas to Avoid.

The route could not avoid the speci-

fied area.

Toll road has not been avoided.

If the route to the destination (or way

point) cannot be established by

bypassing toll roads (including toll

areas) and Areas to Avoid.

If the current route is not desired, set

destination or way points that do not

pass through toll roads (including

toll areas) and Areas to Avoid.

Ferry has not been avoided. In case a ferry route was included in

the route to the destination or way

points even though “Avoid Ferry”

was set to “On”.

If the current route is not desired, set

destination or way points that do not

pass through a ferry route.

Toll road has not been avoided. If the route to the destination (or way

point) cannot be established by

bypassing toll roads (including toll

areas).

If the current route is not desired, set

destination or way points that do not

pass through toll roads (including

toll areas).

The address does not exist.

Do you want to continue?

If the house number is entered with-

out specifying City or Street and that

house number does not exist on the

data.

Re-enter the existing house number

by following the instructions shown

on the screen.

Or, proceed to the next step without

entering the house number and

specify the City or Street first.

There is no applicable data for the

selected city. Automatically returning

to list.

If the history data of the City could

not be used (for example, in case

that the history data of the City that

was used in the POI Search cannot

be found in the Address Search.)

Once the search is performed to

specify the City, the result is saved as

a history. The data of the specified

City, however, may not be hit by the

different search criteria. In this case,

try another search method or change

the destination.

There is no Freeway in this area. If no freeway was found in the

selected zone.

Set the destination or way points

using another search method or

change the location of the destina-

tion or way points.

Message When What to do

1 2 ... 67 68 69 70 71 72 73 74 75 76 77 ... 81 82

Comments to this Manuals

No comments

Adesso CNDV-50MT Service Manual Page 72

Comments to this Manuals